now, I am reading your questions on these threads.
These seem so cool.

I am afraid of this new version.
What is the effective way to study?
I dont have real switch and router.

If you have a time, pls give me some advices!!

and continue to stop your site on MSN?
I tried to out message....but I cant. sorry.

Edited by - atsusy on Jun 16 2002 10:58:26 AM

Please note: As I less likely to use the words No & Sorry, Members are requested not to put forword any qurey to me with out up dating your personal profile (Biodata).

You need a Network Termination type 1 or NT1 in short.
The customer Premise side of the NT1 is the S/T reference point, And the interface of Local Loop at the NT1 is called the U reference point. Now don't ask me what is a NT1 and what's a Local loop? Better go through PPP,ISDN & FRAME-RELAY chapter's at list twice before sitting for the exam on Wednesday.
Good Luck!
Love
Tara

Question:-- The following statement would deny traffic from what subnets? Router_B(config)#access-list 101 deny tcp 10.1.8.0 0.0.7.255 192.16.5.0 0.0.0.255

A) 10.1.8.0
B) 10.1.15.0
C) 10.1.0.0
D) 10.1.16.0
E) choice a and b

Question:-- The Serial 0/0 IPX encapsulation of Router_A is:

A) Novell-ether
B) SAP
C) ARPA
D) SNAP
E) Can not be determined
F) HDLC
Please note:The default encapsulation for a serial interface of Cisco router is HDLC

i oredi update my profile.Tahnk you.

steven

quote:

---

hai tara hava a doubt
1. A PRI S/T interface on a Cisco router needs a ________ to connect to the U reference point..

---

hai tara does csu/dsu has anything to do withthis I mean if the option had csu/dsu can this be the write answer.

quote:

---

*TARA'S FIFTY OUT OF FIFTY*

Question:-- find usable network & usable hosts for network address 201.105.13.0/26

A:64networks 4hosts
B:4networks 64hosts
C:3networks 63hosts
D:62networks 2hosts
For correct answer you must click on the writing pad icon and write 2 networks & 62 usable hosts and submit.

Members are requested to go through
Cisco's first year & second year CCNA Companion guide
to know more about the subject rather then collecting question & answer.

Love

Tara's Help Desk.

---

Tara, I've updated my profile. I don't understand what the answer is. Can you explain it to me?

Dear Bob,
Please wait for my detailed reply soon.
Thanks for your patience?
Love
Tara

Edited by - Tara on Jun 18 2002 06:25:16 AM

Question:-- With one method of transmitting fames through a switch the switch receives the complete frame and checks the frame CRC before forwarding the frame. What is this transmitting method called?

A. CSMA/CD
B. Full duplex.
C. Cut through.
D. Half duplex.
E. Fragmentation.
F. Stored and forwarded.

Question:-- Which two physical interfaces support PPP? (Choose two)
A.Ethernet
B.Token Ring
C.synchronous serial
D.asynchronous serial

I pass the exam ccna. i'd like to say thank you for your help .
for those who is going to be there ...don't worry, the exam is not so bad actually it's easy if you are did the 500 Q and the 127 Q but emphasis on but you understand the Q and the answer .if you just recall the answer so forget it ypu will not pass the exam..the key is to understand the principle and concepts.

for tara.. do you know where I can find a good book for rhe BSCN exam
if you have any idea i will happy to hear..

thank's

yoram

Question:-- When you issue the command show version, your router returns: “Configuration register is 0x0101”
From where does the router boot?

A. ROM
B. NVRAM
C. FLASH
D. A TFTP server

Please Read the boot-up sequence of the router & memorize, its very important*

Question:-- Which command displays the interfaces using a given access list?

A. Show filters
B. Show IP interface
C. Show active list
D. Show interface parameters
E. Configure IP access list
F. Show access-list interfaces

1.which command will provide you with information regarding the layer 3 configuration of directly connnected router interfaces?

2.which of the following are not true of standard half-duplex Ethernet circuitry?
A. It is alternate one-way communication.
B. The receive (RX) is wired directly to the transmit(TX) of the remote station.
C. The receive (TX) is wired directly to the receive (RX) of the remote station.
d. collisions are not possible.
e. Both stations can transmit simultaneously.
Answere was A.. ( I think it is D,E).

3. do u know a link in cisco website which gives info about holddown timers..( I want to know when does the holdon timer for igrp resets)

4.is no cdp run command available in 1900. Transcender say s catalyst 1900 doesn't has no cdp run command..

Edited by - aspire on Jun 20 2002 04:59:12 AM

Question:-- What is the bit length and expression form of a MAC address?

A. 24 bits expression as a decimal number
B. 24 bits expression as a hexadecimal number
C. 36 bits expression as a binary number
D. 48 bits expression as a decimal number
E. 48 bits expression as a hexadecimal number

Question:-- Which range of possible numbers do standard IPX access -lists have?

A. 100 - 199
B. 600 - 699
C. 800 - 899
D. 1000 - 1099

Dear Bob,
Fine & Thank you for your patience! You are not a Dumb.We should always feel Positive towards our Goal and our Life. You are only 22,its a long way to go. You would have taken your A+ first.But what ever done is done? Now compleat your CCNA first and try to get what ever offer comes in the way even its a peanut salary say welcome. And try to gather some experience while persuing the other certification you have mentioned.Hope you feel better now?
Best wishes
Love
Tara

Edited by - Tara on Jun 21 2002 07:23:34 AM

Question:-- Modem networks are often described as using 100Base-TX components. What is meant by the term 'Base' in this definition?

A. It describes the signaling method for communication on the network.
B. It refers to the type of media used in the network.
C. It relates to the speed of transmission of network signals.
D. It defines the allowable length of media that can be used.
E. It defines half-duplex or full-duplex operation.

Question:-- What are two purposes of segmenting a network with a bridge? (Choose two).

A. To reduce collisions.
B. To increase collisions.
C. To add collision domains.
D. To reduce collision domains.
E. To have more broadcast domains.