Question:-- Which IOS command would you use to copy your saved configuration to a TFTP server?

a. copy nvram tftp
b. copy startup tftp
c. copy running tftp

Question:-- The following function is performed by what layer of the OSI Reference model: Provides synchronization between address and name databases

a. Application
b. Presentation
c. Session
d. Transport
e. Network

Question:-- A "#" symbol at the end of your router's hostname prompt indicates:

a. That you are in configuration mode
b. That you are in read-only mode
c. That you are in enabled mode (privileged mode)
d. That you are in EXEC mode

1)Which of the following are reasons to use a bridge to segment a network?(choose two)
A. to reduce broadcasts within collision domains
B. to reduce collisions within broadcast domains
C. to Increase the number of broadcast domains
D. to Increase broadcasts within collision domains
E. to Increase the number of collisions domains
F. to Increase
Answer B,E or B,D

2)Which commands could be used at the command line interface to troubleshoot LAN
connectivity problems on a router?(Choose three)
A. ping
B. tracert
C. ipconfig
D. show ip route
E. winipcfp
F. show interfaces
Answer A,D,F

3)You are configuring a new catalyst switch that want to manage remotely from workstations on other network segment within your enterprise E. which of the following are required to allow remote management of the switch over ip?(choose two)
A. The switch name must match the workgroup name of the local network.
B. The switch must be configured with an IP address and default gateway.
C. The remote workstations must have access to the management VLAN of the switch
D. CDP must be enabled on the switch so shat it can be located by other devices on the
network.
Answer A,C or B,C.

4)You telnet to a host on a remote network. Which MAC address will be present in the
ARP table when you issue the show arp command?
A. MAC address of the destination host Ethernet port
B. MAC address of the local router Ethernet port
C. MAC address of the destination router Serial port
D. MAC address of the local router Serial port
Answer B

5)What are possible causes of LAN traffic congestion?(choose four)
A. too many hosts In a broadcast domain
B. full duplex operation
C. Broadcast storms
D. multicasting
E. segmentation
F. low bandwidth
Answer A,C,E,F

6)Which of the following are benefits of VLANs?(choose three)
A. They Increase the size of collision domains.
B. They allow logical grouping of users by function.
C. They can enhance network security.
D. They Increase the size of broadcast domains while decreasing the number of broadcast domains
E. They Increase the number of broadcast domains while decreasing their size.
F. They simplify switch administration.
Answer B,C,E or C,E,F
7)Which of the following statements regarding routed and routing protocols are true?(choose 2)
A. A routed protocol Is assigned to an Interface and determines the method of packet delivery.
B. A routing protocol determines the path of a packet through a network.
C. A routed protocol determines the path of a packet through a network.
D. A routing protocol operates at the transport layer of the OS1 model.
E. A routed protocol updates the routing table of a router.
Answer A,B

8)You had configured the routing table. you press show run, found that you s0 is shut down. What the inFORMation will display in the first line!
a. the s0 is shut down, protocol is shut down.
b. the s0 is up . protocol is up
c. the s0 is adiministerly up. protocol is up
d. the s0 is adiministerly down. protocol is down
e. the s0 is adiministerly up . protocol is down
Answer A

9)Which wan equipment provides the best quality and quantity about data and signal?
a. isdn
b. atm
c. fddi
d. token ring
Answer A or B

10) Which of these is fast digital signal and packed switched?
A. isdn
B. frame relay
C. atm
D. fddi
Answer A

11) What are 4 ways network management can be simplified by using the virtual LANs (VLANs)?(Choose four)
A. VLANs allow you to implement multiple layers switching easily.
B. VLAN can group several broadcasts domains into multiple logical subnets.
C. It is no longer necessary to install cables to move a user from a new network to another.
D. Network adds, moves and changes are achieved by configuring a port into a VLAN.
E. A group of users needing high security can be put into a VLAN so that no users outside the VLANs can communicate with them.
F. As a logical grouping of users, VLANs can be considered independent from their physical or geographic locations.
Answer B,C,D,F

12) Switching methods include cut-through, store and forwarded and a modified version of the first two methods. Which statement about switching methods is true?
A. The stored and forward method has low latency.
B. The cut through method and switching has high latency.
C. The modified version holds the packet in memory until 50% of the packet reaches the switch.
D. The modified version holds the packet in memory until the data portion of the packet reaches the switch.
Answer Don't know either C or D

13) Which two statements about frame tagging are true? (Choose two )
A. A filtering table is developed for each switch
B. Frame tagging assigns a unique user defined ID to each frame
C. A unique identifier is placed in the header of each frame as it is forwarded between switches
D. Frame tagging is a technique that examines particular information about each frame based on user defined offsets
Answer B,C or B,D

Edited by - bob718 on Jul 15 2002 01:24:44 AM

1. (BE)

2. (ADF)

3. (BC)

4. (B)

5. (ACDF)

6. (BCE)

7. (AB)

8. (A)

9. (B)

10. (A)

11. (CDEF)

12. (D)

13. (BC)

Please go through The Books And verify why it is so?
Love
Tara

Edited by - Tara on Jul 15 2002 10:57:57 AM

Question:-- An IP address is an address burned into a NIC card by the manufacturer

a. True
b. False

Question:-- What is the syntax to add a banner to a Cisco router configuration?

a. banner
b. banner #
c. banner motd #
d. motd banner #

1)In which three situations is a hold-down timer reset? (Choose three.)
A. When the hold-down timer expires.
B. When infinity is finally defined as some maximum number.
C. When the router exchanges update summaries at area borders.
D. When the router detect faulty LSPs propagating through the internetwork.
E. When another update is received indicating a new route with a better metric.
F. When another update is received indicating the original route to the network has been
restored.
G. When the router receives a processing task proportional to the number of links in the
internetwork.
Answer A,E,G

2)Which command should you use to configure a router so that it can become a TFTP host for router system image that is run in Flash?
A. Copy flash tftp
B. Config tftp server
C. Write network
D. Tftp-server system
E. Setup server tftp
Answer D

3)Which two statements about a reliable connection oriented data transfer are true?
(Choose two)
A. Recipients acknowledge receipt of data
B. When tankers are filled to capacity, datagrams are discarded and not retransmitted
C. Windows are used to control the amount in outstanding acknowledged data segments
D. If the sender a timer expires before receipt of an acknowledgment the sender drops
the connection
E. The receiving device waits for acknowledgments from the sending device before
accepting more data segments
Answer A,D

4)Calculate the number of usable networks and usable hosts for the network
210.106.14.0/24.
A. 1 network with 254 hosts
B. 2 networks with 128 hosts
C. 4 networks with 64 hosts
D. 6 networks with 30 hosts
Answer C?

5)With the hierarchical numbering of IP addresses what determines the portion of the
address that will identify the network number?
A. Subnet Mask
B. Dots between octets
C. Class of first octet
D. Assignments of DHCP
E. Address-resolution process
Answer A or C

6)What are four function/characteristics of the network layer of the OSI model?
(Choose four)
A. It uses a two-part address.
B. It maintains routing tables.
C. It uses broadcast addresses.
D. It establishes network addresses.
E. It provides access to the LAN media.
F. It provides media independence for upper layers.
G. It provides path selection for Internet work communication.
Answer A,B,C,D

7)What is the protocol and what is the purpose of the following address?
238.255.255.255
A. IPX; a SAP broadcast
B. IP; a multicast group
C. IP; a reserved address
D. IP; a directed broadcast
E. IPX; a flooded broadcast
Answer A or D

8)Which three basic switch functions increase available bandwidth on the network?
(Choose three)
A. Loop avoidance.
B. Address learning
C. Hop count limiting
D. Broadcast filtering
E. Packet forward/filtering.
Answer A,B,D

9)Which of the following are true regarding passwords on a Cisco router? choose 4
A. All passwords can be encrypted.
B. All passwords can be entered using the set-up dialogue.
C. A password can be set before a user can enter the privileged mode.
D. A password can be set for individual lines.
E. TACACS or Radius password authentication can be used.
Answer A,C,D,E

10) Which IOS command is used to associate an ISDN phone number with the next hop
router address?
A. isdn destination number
B. dialer map
C. isdn spid1
D. isdn line number
Answer B or C

11 What are the advantages of using the OSI layered network model? (choose three)
A. Allows multiple-vendor development through standardization of network components.
B. Creates a list of communication rules that all companies must implement to get onto
the Internet.
C. Allows various types of network hardware and software to communicate.
D. Prevents changes In one layer from affecting other layers, so It does not hamper
development
E. Allows companies to develop proprietary Interfaces
Answer A,D,E

Edited by - bob718 on Jul 15 2002 11:40:22 PM

1. A, E, G

2. A. Copy flash tftp

3. A, C

4. A. 1 network with 254 hosts

5. C. Class of first octet

6. A, B, D, G

7. D. IP; a directed broadcast

8. A, B, D

9. A, C, D, E

10.B. dialer map

11.A, C, D

Better change your exam date to save disapointments?
Love
Tara

Question:-- The following function is performed by what layer of the OSI Reference model: Fragments and reassembles packets while managing network layer connections

a. Presentation
b. Session
c. Transport
d. Network
e. Data Link

Question:-- What is the first thing that you are asked when running setup on a Cisco IOS router?

a. Would you like to enter the initial configuration dialog?
b. Would you like to see the current interface summary?
c. Enter host name [Router]:
e. Enter an initial configuration using the setup command.

Tara, I am Marcus, from Sweden, but living in the UK. I am hoping to sit the exam on Monday and am struggling with some questions.

I will post some of them and see if you have any ideas.

Many thanks.

1. A network is very congested. Currently all the devices are connected through a hub. Which solution would best decrease congestion on the network?
A. Add a second hub
B. Replace the hub with a router.
C. Replace the hub with a switch.
D. Replace the hub with a repeater.

I would have thought replacing the hub with a switch, as the router could cause bottlenecks, but I have heard using a Router is potentially the recommendation.

2. The exhibit shows the Cisco routers startup messages.
Which group of messages identifies the router components that you can configure during set up the initial system configuration?
A) System Bootstrap, Version 11.3(1)XA, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1) Copyright (c) 1998 by cisco Systems, Inc, CS2600 platform with 32768 Kbytes of main memory
B) Rp,,pm 1 b f program load complete, entry point: 0x800008000, size: 0xef4e0 Self decompressing the image :############################[OK]
C) Notice: NVRAM invalid, possible due to write erase,
program load complete, entry point:0x80008000, size 0x415b20 Self decompressing the image: ###################################
##########################################################[OK]
Restricted Rights Legend….(abridged)
D) Cisco Internetwork Operating System Software
IOC (tm) C2600 Software (C2600-JS-M), Version 11.3(2)XA,
PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
Copyright 1996-1998 by Cisco Systems Inc.
Compiled 10-Mar-98 14:25 by gneale
Image text-bas: 0x80008084, database: 0x809CD49C
E) Cisco 2611 (MP C860) processor (revision 0x100) with 24576K/8192K bytes of memory,
Processor board ID 04614954
M860 processor, part number 0 mask 32,
Bridging software, X25 software, Version 3.0.0,
2 Ethernet/IEEE 802.3 interface(s)

I have little idea as to whether D or E is correct. I have scoured the Sybex and ICND books to little avail. I understand that D shows the code image running, and I also understand why it cannot be A,B or C...but can I rule out E?

3. You telnet to a host on a remote network. Which MAC address will be present in the ARP table when you issue the show arp command?
A. MAC address of the destination host Ethernet port.
B. MAC address of the local router Ethernet port
C. MAC address of the destination router Serial port
D. MAC address of the local router Serial Port

I would say B as an ARP broadcast will not traverse routers... but I may be missing something?

4. What is the purpose of Spanning-Tree in a switched LAN?
A. To provide a mechanism for network monitoring in switched environments.
B. To prevent routing loops in networks with redundant paths.
C. To prevent routing switching loops in networks with redundant switched paths.
D. To manage, the addition, deletion, and naming of VLANs across multiple switches.
E. To segment a network into multiple collision domains.

I am leaning toward C as we are dealing with switching, but B doesn't seem entirely incorrect either.

Any input/feedback/debates more than welcome :)

Thanks in advance

Marcus

1. C. Replace the hub with a switch. (As you can segment the LAN with switch to give more bandwidth & reduce collision)
2. D. (Look what happens after you type " SHOW VERSION")
3. B. MAC address of the local router Ethernet port (When you Telnet You are no more in your Router?)
4. C. To prevent routing switching loops in networks with redundant switched paths.
(Spanning Tree Protocol is used only In switching environment)
Hope no more struggling?
world is a Circus?
Love
Tara

Edited by - Tara on Jul 19 2002 10:52:07 PM

Question:-- Windowing is used by network devices to temporarily store bursts of excess data in memory until they can be processed.

a. True
b. False

Question:-- What command can you use on a Cisco IOS router to display the session commands that you have used?

a. show users
b. who
c. show memory
d. show history

OK, I am sure everyone has heard all the horror stories about the simulations crashing part way through? That would be horrible! Anyhow, there is a VUE testing centre very near to me and I was going to book there. I want to invite people to share any experiences that they may have had/heard of. From what I have heard, Prometric seem to be the ones that don't seem to have it quite right. I have not heard anything bad about VUE...yet.

Plus, Cisco say that there are 2 general types of simulation; configuration & troubleshooting. The configuration should be a doddle, but the troubleshooting seems a little vague. Is it simply a matter of checking the config on the router in question (ie show run), checking the config & re-doing any config that may be unhappy/non-existant? I am hoping they are more concerned with this (that is, the candidate supplying a proper working config) than whether the candidate runs any pings, or show interfaces, or or or.

Also, what is the deal with connecting to the routers. I have read horror stories on that also, with some people not able to connect from any host, or having to play around with terminal settings etc. I would have thought at least that part would be straight forward and painless, so the testing candidate can get to what really matters - configuring the router. Are there any settings that need to be put in, or is it just like their web site shows - just click on the host and select 'terminal', hit OK and away you go?

I read on the Cisco site & it states that shortcuts are cool, and you don't need to do a copy run start (which seems pretty odd really). I am going to do a copy run start just to be safe. Surely you can't be penalised for doing it?

Anyhow, from what I can gather, if you mess up the simulations, you will not pass the exam. I reckon the concepts will be pretty straight forward, but the testing software sounds like it could be a pain

What says you guys?

Question:-- Which layer of the OSI reference model enables multiple data links to be combined into an inter-network?

a. Layer 5
b. Layer 3
c. Layer 4
d. Layer 7
e. Layer 6

Question:-- Which of the statements would be valid for configuring the IP address on a router's interface?

a. ip address 200.111.5.1 255.255.255.
b. ip address 200.285.100.254 255.255.255.224
c. ip unnumbered ethernet0
d. ip-address 200.111.5.1
e. ip address 255.255.255.0 200.111.5.1

I'm a newbie 2 this group but have a basic and working knowledge of Networks.
Sorry to cut in suddenly but I think the answer to Marcus's Q.4 should be (C.) To prevent routing switching loops in networks with redundant switched paths. STP does this in Layer-2 by electing a root bridge.
The answer B. Routing loops (caused by slow convergence of D-V protocols hence routers are not updated same time) in a Network are prevented by: Split Horizon, Maximum Hop count, Holddowns & Route Poisoning.

What do you think - Correct me if I'm wrong.

B. IBI

I have been reading this forum through and through and disecting every post just about, but I just now got around to registering :D
I will also be taking my exam very shortly and have found the info in this thread to be a great help. I also read about the unfortunate happenings a while back where files where deleted :(

I tried to join the CCNA607 group but have not gained access yet. My true endevour is to attain these questions everyone has been so desperate to get their hands on from what I have read. These seem to be a great source of knowlege, and have aided many during their trials to get their certification.

I would be very greatful for any help anyone could give me regarding this issue and these questions. My bio is up to date with sufficient information I hope and if not just let me know and i'd be happy to add more aside from my social security number :D

thanks for your help and your time

quote:

---

Hi to Everybody!!
From today "TARA'S HELP DESK" starts for the wouldbe CCNA's To help them in all possible ways to get them certified through this topic. All your doubt and questions regarding exam#640-607 and your remark's should be posted through the reply icon,after going through this topic,(which is in the rightside of the topic row).
Those who are sitting for the exam I request them to visit
http://www.cisco.com/warp/public/10/wwtraining/ or
visit to, http://groups.msn.com/CCNA607
to go through verious subject on exam#640-607 to familiarize them about the type of topics they will be asked in the exam.Those who are preparing for latter date can go through the subneting review, subneting Practice, and other postings as well.
Hope this will help in a better way towards preparing for your exam.
Raise your problem as well,under the same topic to make it a succsess. Read this topic often to get through all the posting under this Topic.
Good Luck
Love
Tara

Look forward to Topic "How to make best out of those 75 minutes"

Edited by - Tara on Jul 02 2002 10:33:57 AM

---

manishsingh

quote:

---

Hi to Everybody!!
From today "TARA'S HELP DESK" starts for the wouldbe CCNA's To help them in all possible ways to get them certified through this topic. All your doubt and questions regarding exam#640-607 and your remark's should be posted through the reply icon,after going through this topic,(which is in the rightside of the topic row).
Those who are sitting for the exam I request them to visit
http://www.cisco.com/warp/public/10/wwtraining/ or
visit to, http://groups.msn.com/CCNA607
to go through verious subject on exam#640-607 to familiarize them about the type of topics they will be asked in the exam.Those who are preparing for latter date can go through the subneting review, subneting Practice, and other postings as well.
Hope this will help in a better way towards preparing for your exam.
Raise your problem as well,under the same topic to make it a succsess. Read this topic often to get through all the posting under this Topic.
Good Luck
Love
Tara

Look forward to Topic "How to make best out of those 75 minutes"

Edited by - Tara on Jul 02 2002 10:33:57 AM

---

Prem

quote:

---

Hi to Everybody!!
From today "TARA'S HELP DESK" starts for the wouldbe CCNA's To help them in all possible ways to get them certified through this topic. All your doubt and questions regarding exam#640-607 and your remark's should be posted through the reply icon,after going through this topic,(which is in the rightside of the topic row).
Those who are sitting for the exam I request them to visit
http://www.cisco.com/warp/public/10/wwtraining/ or
visit to, http://groups.msn.com/CCNA607
to go through verious subject on exam#640-607 to familiarize them about the type of topics they will be asked in the exam.Those who are preparing for latter date can go through the subneting review, subneting Practice, and other postings as well.
Hope this will help in a better way towards preparing for your exam.
Raise your problem as well,under the same topic to make it a succsess. Read this topic often to get through all the posting under this Topic.
Good Luck
Love
Tara

Look forward to Topic "How to make best out of those 75 minutes"

Edited by - Tara on Jul 02 2002 10:33:57 AM

---

Prem

quote:

---

Hi to Everybody!!
From today "TARA'S HELP DESK" starts for the wouldbe CCNA's To help them in all possible ways to get them certified through this topic. All your doubt and questions regarding exam#640-607 and your remark's should be posted through the reply icon,after going through this topic,(which is in the rightside of the topic row).
Those who are sitting for the exam I request them to visit
http://www.cisco.com/warp/public/10/wwtraining/ or
visit to, http://groups.msn.com/CCNA607
to go through verious subject on exam#640-607 to familiarize them about the type of topics they will be asked in the exam.Those who are preparing for latter date can go through the subneting review, subneting Practice, and other postings as well.
Hope this will help in a better way towards preparing for your exam.
Raise your problem as well,under the same topic to make it a succsess. Read this topic often to get through all the posting under this Topic.
Good Luck
Love
Tara

Look forward to Topic "How to make best out of those 75 minutes"

Edited by - Tara on Jul 02 2002 10:33:57 AM

---

Prem

quote:

---

Hi to Everybody!!
From today "TARA'S HELP DESK" starts for the wouldbe CCNA's To help them in all possible ways to get them certified through this topic. All your doubt and questions regarding exam#640-607 and your remark's should be posted through the reply icon,after going through this topic,(which is in the rightside of the topic row).
Those who are sitting for the exam I request them to visit
http://www.cisco.com/warp/public/10/wwtraining/ or
visit to, http://groups.msn.com/CCNA607
to go through verious subject on exam#640-607 to familiarize them about the type of topics they will be asked in the exam.Those who are preparing for latter date can go through the subneting review, subneting Practice, and other postings as well.
Hope this will help in a better way towards preparing for your exam.
Raise your problem as well,under the same topic to make it a succsess. Read this topic often to get through all the posting under this Topic.
Good Luck
Love
Tara

Look forward to Topic "How to make best out of those 75 minutes"

Edited by - Tara on Jul 02 2002 10:33:57 AM

---

Prem

quote:

---

Hi to Everybody!!
From today "TARA'S HELP DESK" starts for the wouldbe CCNA's To help them in all possible ways to get them certified through this topic. All your doubt and questions regarding exam#640-607 and your remark's should be posted through the reply icon,after going through this topic,(which is in the rightside of the topic row).
Those who are sitting for the exam I request them to visit
http://www.cisco.com/warp/public/10/wwtraining/ or
visit to, http://groups.msn.com/CCNA607
to go through verious subject on exam#640-607 to familiarize them about the type of topics they will be asked in the exam.Those who are preparing for latter date can go through the subneting review, subneting Practice, and other postings as well.
Hope this will help in a better way towards preparing for your exam.
Raise your problem as well,under the same topic to make it a succsess. Read this topic often to get through all the posting under this Topic.
Good Luck
Love
Tara

Look forward to Topic "How to make best out of those 75 minutes"

Edited by - Tara on Jul 02 2002 10:33:57 AM

---

Prem

quote:

---

Hi to Everybody!!
From today "TARA'S HELP DESK" starts for the wouldbe CCNA's To help them in all possible ways to get them certified through this topic. All your doubt and questions regarding exam#640-607 and your remark's should be posted through the reply icon,after going through this topic,(which is in the rightside of the topic row).
Those who are sitting for the exam I request them to visit
http://www.cisco.com/warp/public/10/wwtraining/ or
visit to, http://groups.msn.com/CCNA607
to go through verious subject on exam#640-607 to familiarize them about the type of topics they will be asked in the exam.Those who are preparing for latter date can go through the subneting review, subneting Practice, and other postings as well.
Hope this will help in a better way towards preparing for your exam.
Raise your problem as well,under the same topic to make it a succsess. Read this topic often to get through all the posting under this Topic.
Good Luck
Love
Tara

Look forward to Topic "How to make best out of those 75 minutes"

Edited by - Tara on Jul 02 2002 10:33:57 AM

---

Prem